徐州INA軸承座過早損壞的原因是什么？我們通常如何判斷這個問題？其工作軸承使用壽命未達到壽寧損壞期，已損壞。應防止軸承座事故。一位工程師得出以下結論。我們一起討論吧。

What is the reason for premature damage of Xuzhou INA bearing seat? How do we usually judge this problem? The service life of its working bearing has not reached Shouning damage period and has been damaged. Bearing seat accident should be prevented. An engineer came to the following conclusion. Let's discuss it together.

實際上，深溝球軸承的軸承座，尤其是其外圈直徑表面，是球形的。深溝球軸承的功能基本相同。它可以裝配在相應的TR軸承座凹球面上起到校準作用。對此，我們需要學會如何處理相對早期的損壞，安*全指導如何選擇合適的潤滑劑或潤滑劑，使用正確的潤滑和填充方法來損壞軸承座。

In fact, the bearing seat of deep groove ball bearing, especially its outer ring diameter surface, is spherical. The functions of deep groove ball bearings are basically the same. It can be assembled on the concave spherical surface of the corresponding TR bearing seat to play a calibration role. In this regard, we need to learn how to deal with relatively early damage, safety guidance on how to choose the appropriate lubricant or lubricant, using the correct lubrication and filling bs to damage the bearing seat.

1。選擇特殊合適的安裝工具，安裝后使用專用儀器對徐州INA軸承進行測試。

1. Select special and suitable installation tools, and use special instruments to test Xuzhou INA bearing after installation.

2。使用前，**好不要拆卸軸承座的填料，保持安裝環境清潔，清洗要使用的軸承，并加強軸承的密封裝置。

2. Before use, ** Do not dismantle the packing of the bearing seat, keep the installation environment clean, clean the bearing to be used, and strengthen the sealing device of the bearing.

3。軸承座長期超載運行；維護不及時；維護不當；設備老化等。

3. Bearing seat long-term overload operation; maintenance is not timely; improper maintenance; equipment aging and so on.

一般來說，非標軸承在開始運行后溫度會升高。經過一段時間后，軸承將在較低的溫度（通常比室溫高10-40度）下處于正常狀態。正常運行時間根據徐州INA軸承的尺寸、形狀、速度和潤滑方式而變化，非標準軸承周圍的散熱條件也不同。大約需要20分鐘到幾個小時。

Generally speaking, the temperature of non-standard bearings will rise after starting operation. After a period of time, the bearing will be in normal condition at a lower temperature (usually 10-40 degrees higher than room temperature). Normal operation time varies according to the size, shape, speed and lubrication mode of Xuzhou INA bearings, and the heat dissipation conditions around non-standard bearings are also different. It takes about 20 minutes to a few hours.

當非標準軸承的溫度沒有達到正常，出現異常溫升時，可以考慮以下原因。此外，應盡快實施停機，并采取必要的對策。溫度對于維持非標軸承的正常使用壽命和防止潤滑劑的劣化非常重要。有針對性的建議：盡力控制使用非高溫（一般小于100度）。溫度異常升高的主要原因是潤滑油過多或過少。軸承安裝不 。非標徐州INA軸承的內間隙過小或載荷過大。密封裝置的摩擦太大了。潤滑劑不匹配。交配表面的蠕變。

When the temperature of non-standard bearings does not reach normal and abnormal temperature rise occurs, the following reasons can be considered. In addition, shutdown should be implemented as soon as possible and necessary countermeasures should be taken. Temperature is very important for maintaining normal service life of non-standard bearings and preventing deterioration of lubricants. Targeted recommendations: try to control the use of non-high temperature (generally less than 100 degrees). The main reason for abnormal temperature rise is too much or too little lubricating oil. No bearing installation. The inner bance of non-standard Xuzhou INA bearing is too small or the load is too large. The friction of the sealing device is too great. Lubricant mismatch. Creep of mating surface.

1。首先，潤滑軸承的所有部分，以減少摩擦和磨損。

1. First, lubricate all parts of the bearing to reduce friction and wear.

2。為了延長非標準軸承的疲勞壽命，在軸承的滾動接觸面上往往會形成適當的油膜。

2. In order to prolong the fatigue life of non-standard bearings, an appropriate oil film is often bed on the rolling contact surface of bearings.

3。由于摩擦或其余原因在軸承中產生的熱量通過潤滑進行消磨。

3. Heat generated in bearings due to friction or other reasons is dissipated by lubrication.

4。非標準軸承可以潤滑，以防止生銹和灰塵。

4. Non-standard bearings can be lubricated to prevent rust and dust.

因此，應正確認識軸承潤滑的重要性，提高軸承的性能，降低消耗。

Therefore, we should correctly recognize the importance of bearing lubrication, improve the perbance of bearings and reduce consumption.

文章來自：徐州SKF軸承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章來自：徐州INA軸承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章來自：徐州NSK軸承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757